Expert Diesel Knowledge. Always Free.
Diesel technician using a diagnostic tablet to investigate DEF and SCR system faults on a heavy-duty semi-truck while a fleet maintenance professional observes inside a commercial repair shop.

DEF Derate Rules: Stages, EPA Proposal and Fleet Impact

By Michael Nielsen, Publisher | 15+ Years in Diesel Repair & Fleet Operations

Last Updated: November 2026

⏱ Estimated reading time: 13 minutes

DEF derate rules are the federal and manufacturer requirements that cut engine power, and later vehicle speed, when a diesel truck's selective catalytic reduction (SCR) system detects a diesel exhaust fluid (DEF) or emissions fault. EPA calls this an inducement. As of November 2026, heavy-duty trucks follow staged torque cuts ending at 25 mph, and EPA has proposed removing derates from new engines. That proposal is not final.

This Heavy Duty Journal guide explains the current stages, what triggers them, what EPA proposed in July 2026 and where the proposal stands. It also covers manufacturer software updates, the shop and fleet steps that matter now, and what HDJ could not confirm. HDJ's DEF warning light guide and DEF system problems guide cover diagnosis in more detail.

Key Takeaways

  • 01Derates are staged. EPA's August 2025 guidance sets heavy-duty truck stages at 15 percent, then 30 percent torque cuts, then 25 mph.
  • 02The old final step was 5 mph. Before the guidance, the last stage was 5 mph after 4 hours.
  • 03Updates are rolling out. Cummins, Paccar and Daimler Truck North America released calibration updates in 2026.
  • 04The ban is only proposed. EPA proposed on July 9, 2026 to remove derates for new engines; comments closed August 29.
  • 05Sensors can cause false derates. EPA says a failed sensor can trigger an inducement even when DEF is sufficient.
  • 06Do not delete the system. Only manufacturer-approved software changes avoid tampering problems.

01

What a DEF Derate Is

A DEF derate is a reduction in engine torque or vehicle speed that the engine control module applies when the emissions system cannot confirm the exhaust is clean. DEF derate rules come from EPA's inducement requirements for SCR engines, which exist to push drivers to refill DEF or fix a fault. SCR is the system that injects DEF into the exhaust to reduce nitrogen oxides (NOx).

Understanding DEF derate rules matters because the derate arrives in steps, and each step changes what a driver and a shop can do. A truck may run for days with reduced torque before the speed limit applies, so the first warning is the cheapest time to act.

The derate is not a mechanical failure. It is a programmed response, and its timing depends on the engine maker's calibration within EPA's limits. That is why two trucks with the same fault can behave differently, and why a software update can change when a derate starts.

02

Current DEF Derate Rules

Current DEF derate rules for heavy-duty trucks give three stages before the final speed limit. EPA's August 2025 guidance letter sets the first stage at 650 miles or 10 hours, with a 15 percent torque reduction, then 30 percent at 4,200 miles or 80 hours, then 25 mph at 8,400 miles or 160 hours (EPA guidance IACD-2025-10).

Exhibit 1. Inducement stages in EPA's August 2025 guidance, as of November 2026
Vehicle classInitial stageSecondary stageFinal stage
Heavy-duty trucks650 mi / 10 hr: 15% torque cut4,200 mi / 80 hr: 30% torque cut8,400 mi / 160 hr: 25 mph
Motor coaches3,000 mi / 40 hr: 10% torque cutNone10,500 mi / 200 hr: 50 mph
Chassis-certified vehiclesNoneNone4,200 mi / 80 hr: 45 mph

Nonroad equipment follows a different schedule under the same guidance: a 25 percent torque cut at 36 hours and a 50 percent cut at 100 hours, with no final speed step. EPA's March 2026 fact sheet adds that agricultural equipment can run up to 100 hours before inducement, up from 4 hours. These DEF derate rules differ by class, so check which class a unit falls in.

EPA's companion fact sheet lists the earlier final step for every class as 5 mph after 4 hours. EPA also says the guidance expects new on-road diesels from model year 2027 to be engineered to avoid sudden, severe power loss after DEF runs out, and it urges makers to update software in existing vehicles.

03

Manufacturer Software Updates

Manufacturer software updates are how the August 2025 guidance reaches trucks already on the road. The updates lengthen the time before a DEF derate and raise the final speed limit, but the fault still has to be fixed. Detroit parent Daimler Truck North America said vehicles "must still be repaired to ensure environmental standards are met."

Exhibit 2. Reported 2026 software updates for in-use trucks
MakerEngines coveredDeliveryReport
CumminsAll EPA-certified on-highway SCR engines; over 1.5 million, some from MY2017Calibration updates; more MY2026 engines from mid-August 2026Transport Topics, July 2026
PaccarMX-11 and MX-13Factory after July 20, 2026; Peterbilt and Kenworth dealers for builds after 2018Transport Topics, July 2026
Daimler Truck North AmericaDD15 MY2021-2025; DD13 MY2022-2025, about 330,000 trucksRolling out since February 2026 through 2026HDT, June 18, 2026

DTNA described its update as a warning light only for 650 miles or 10 hours, then a 15 percent derate for up to 4,200 miles, then 25 mph after 10,500 miles. Those stages differ from the EPA table, which shows why a fleet must ask each maker which calibration its trucks run. HDJ did not find whether Paccar's dealer update covers trucks built before 2018.

04

What Triggers a Derate

A derate starts when the engine detects that DEF is missing or the SCR system is not working. The common triggers are an empty or low DEF tank, a fault in the SCR system and a sensor failure. EPA says sensors can fail or malfunction and trigger an inducement even when DEF levels are sufficient and no real emissions problem exists (EPA DEF sensor fact sheet).

Cummins says the driver is prompted to act, for example by refilling the tank, repairing a faulty sensor or component, or running a regeneration cycle. EPA cites a 2021 sensor error that caused widespread failures across brands and an industry-wide recall. HDJ's NOx sensor troubleshooting guide and DEF contamination guide cover the two most common field causes.

Stay Current on Emissions Rules

Get weekly updates on emissions rules, diesel maintenance and fleet management strategy from Heavy Duty Journal, delivered to your inbox.

05

EPA's 2026 Proposal

The proposal amends the 2023 heavy-duty rule, which cut the NOx limit from 0.20 to 0.035 g/bhp-hr and added low-load and idle testing that requires heating elements in aftertreatment systems, according to FleetOwner. The same report said some experts estimated the rule could add as much as $15,000 to a model year 2027 power unit. Those costs are the background for the DEF derate rules proposal.

EPA's 2026 proposal would replace derates and speed limits with visible or audible alerts on new engines. EPA announced it on July 9, 2026, and it was published in the Federal Register on July 14 at 91 FR 43154 under docket EPA-HQ-OAR-2026-0728 (Federal Register notice). The proposal keeps the 0.035 g/hp-hr NOx standard, according to FleetOwner and CCJ.

Exhibit 3. Current rules compared with EPA's July 2026 proposal
ItemCurrent, as of November 2026Proposal
Derates on new enginesStaged torque cuts; 25 mph final for heavy-duty trucksRemoved; visible or audible alerts instead
In-use trucksSoftware updates urged and rolling outComment taken on in-use guidance; none issued
Emission warranty, MY2027+2023 rule extends itKeep MY2026 periods
Useful life2023 rule applies longer periods from MY2027Delayed to MY2030
Nonconformance penaltiesNot availableProposed for the MY2027 NOx standard

EPA's fact sheet says the proposal would retain nearly 90 percent of the NOx reductions projected for the 2023 rule. The Federal Register summary estimates purchaser warranty savings of up to $37 billion, including up to $6,000 per diesel vehicle, and net savings of up to $12 billion. These are EPA estimates, and Fleet Maintenance said it could not confirm the per-vehicle figure.

06

Where the Proposal Stands

EPA reached the proposal in steps. In August 2025 it issued DEF guidance, in February 2026 it sent information demands to 14 manufacturers that account for over 80 percent of DEF-system products, and in March 2026 it approved NOx-sensor software updates. The July 2026 proposal followed, according to EPA. Each step aimed at the same problem, which is trucks that derate when nothing is wrong.

As of November 2026, the proposal is not final. EPA held virtual hearings on July 29 and 30, comments closed on August 29 and EPA's rule page, last updated August 31, shows no final rule (EPA proposed rule page). FleetOwner reported on November 16 that EPA says it is working to finalize quickly, but a decision may not come until 2027.

Exhibit 4. Reported stakeholder positions on the proposal
GroupPositionReported by
ATAApplauded ending derates and rolling back warranty and useful-life changesTruck Parts & Service, July 2026
OOIDAUrged EPA to keep 450,000-mile warranty coverageTruck Parts & Service, July 2026
NATSO and SIGMAWarned of confusion and possible DEF availability and price effectsTruck Parts & Service, July 2026
EMACalled codifying the rule by year end "critical"CCJ, July 2026
Environmental Defense FundOpposes the rollbackFleet Maintenance, July 2026

Industry reaction is mixed, and the table reflects how each group framed it. HDJ takes no position on the proposal. A final rule could change the warranty, useful life and inducement terms in different ways, so fleets should plan for MY2027 purchases without assuming the proposal passes unchanged.

07

What Fleets Should Do Now

Fleets should treat DEF derate rules as a maintenance and records problem now, whatever EPA finalizes. A derate costs a truck its schedule, and the cheapest fixes are supply, software and sensor checks. The list below is HDJ's common-practice approach to the DEF derate rules, and it works with the OEM service information for each engine.

Fleet checklist for DEF derates

  • Ask for the update. Ask the dealer whether each truck has the current manufacturer DEF calibration and keep the answer by unit.
  • Control DEF supply. Keep tanks filled, buy from a controlled source and review HDJ's DEF system maintenance guide.
  • Log every derate. Record date, miles, fault codes, DEF level and the repair, so repeat sensor failures show up.
  • Train drivers. Tell drivers the stages, what the lights mean and who to call before the truck slows.
  • Fix the fault. A software update delays a derate but does not repair the underlying failure.
  • Plan MY2027 buys. Check warranty and derate terms on the specific engine before ordering.

Safety Warning

A final-stage derate can slow a loaded truck to 25 mph on a highway, far below traffic speed. Drivers should act at the first warning, find a safe place to stop and avoid running the truck to the final stage.

08

Shop Triage for a Derate

A shop should check the cheapest causes first and let fault codes steer the rest. Begin with the SPN and FMI codes, as HDJ's SPN and FMI fault code guide explains, then check DEF level and quality, sensor data and the calibration version. Follow the engine maker's procedure for any test.

Exhibit 5. Derate triage order (HDJ common practice; follow OEM service information)
SymptomCheck firstReason
Low-DEF warningTank level and fill sourceEmpty DEF is a defined trigger
Derate with a full tankFault codes, sensor data, calibrationEPA says sensors can trigger inducements with sufficient DEF
Repeat derate after refillDEF quality and SCR codesContamination and SCR faults persist after refilling
Derate after a recent updateDealer confirmation of the calibrationRollout timing varies by platform

HDJ's SCR system troubleshooting guide and 2027 EPA heavy-duty emissions standards guide cover the SCR side and the model year 2027 background. A shop that knows the DEF derate rules can explain each stage to a driver. Document the test results on the work order, because a repeat derate on the same unit is the evidence a warranty claim needs.

Editorial Insight

The HDJ Perspective

According to Heavy Duty Journal, a derate is a records problem before it is a repair problem. In HDJ's field experience across 15+ years of coverage, fleets that log each event by unit see sensor patterns early, while fleets that treat each derate as a one-off pay for the same fault twice.

09

Repair, Tampering and Right to Repair

Right to repair and tampering are separate issues, and the line between them matters. EPA's March 2026 fact sheet says approved NOx sensor-based software updates can be installed on existing engines without being treated as illegal tampering, and that manufacturers can replace urea quality sensors with NOx sensors. It also says owners can repair nonroad diesel equipment, including DEF systems.

That is not permission to disable the SCR system or flash an unapproved derate delete. The fact sheet covers approved manufacturer changes, and EPA's proposal does not authorize deletes. HDJ's diesel emissions tampering penalties guide explains the federal penalty exposure.

42%

reduction in heavy-duty NOx emissions in 2055, compared with having no 2023 rule, that EPA says its proposal would still achieve (EPA fact sheet EPA-420-F-26-012, July 2026).

10

Buying Model Year 2027 Trucks

Model year 2027 truck buyers face DEF derate rules that are still moving. The 2023 rule's extended warranty and useful life would apply unless EPA finalizes its proposal, and EPA proposed nonconformance penalties so makers can sell engines that miss the 0.035 g/hp-hr limit if they pay. FleetOwner reported rates of roughly $1,000 to almost $7,000 per engine.

Ask the dealer for the engine's warranty period in writing, the inducement calibration and the software update plan. HDJ's emission control warranty guide explains the federal warranty basics. A buyer who signs before the final rule should ask how a later change would affect the purchase.

Key Recommendation

Ask your dealer in writing which DEF derate calibration each truck runs and what the warranty terms are, because the final rule may change both after you order.

Truck Fault Code Lookup — decode SPN and FMI codes instantly, get drivability guidance and repair cost estimates, free from Heavy Duty Journal

11

What HDJ Could Not Confirm

HDJ did not find a final version of the DEF derate rules or a date for one, and FleetOwner says it may slip into 2027. HDJ also did not find whether EPA will issue in-use guidance, or a verified figure for the cost of a derate event in downtime. The class-specific warranty miles in the proposal were not on EPA's fact sheet, so this guide uses reported figures only.

The nonconformance penalty amounts come from FleetOwner, not from the Federal Register text HDJ read. One report put the proposal's announcement in June, while EPA and other outlets show July 9. Treat all dates and figures as of November 2026 and check EPA's rule page before relying on them.

FAQ

Frequently Asked Questions

What is a DEF derate?

A DEF derate is a programmed cut in engine torque, and later vehicle speed, when the SCR system detects a DEF or emissions fault. EPA calls it an inducement. It prompts the driver to refill DEF or repair the fault before the truck slows further.

How long until a DEF derate slows my truck to 25 mph?

Under EPA's August 2025 guidance, a heavy-duty truck reaches 25 mph at 8,400 miles or 160 hours after the fault. Earlier stages cut torque by 15 percent and then 30 percent. Manufacturer calibrations differ, so check your maker's version and the exact fault conditions.

Did EPA eliminate DEF derates?

Not yet. EPA proposed on July 9, 2026 to remove derates from new engines and use alerts instead, but comments closed August 29 and no final rule was issued as of FleetOwner's November 16 report. Current inducement rules still apply.

Can a bad sensor cause a DEF derate with a full tank?

Yes. EPA says faulty sensors can trigger an automatic inducement even when DEF levels are sufficient and no real emissions problem exists. A 2021 sensor error caused widespread failures and an industry-wide recall, so check codes and sensor data first.

Do manufacturer software updates remove the derate?

No. The Cummins, Paccar and Daimler updates extend the time before a DEF derate and raise the final speed from 5 mph to 25 mph, but the underlying fault must still be repaired. Delivery depends on the engine and model year, so ask the dealer.

Is it legal to delete a DEF derate with aftermarket software?

Generally no. EPA says approved manufacturer software updates are not tampering, but that does not cover disabling SCR or flashing an unapproved delete. Penalty exposure is federal and real, so use only manufacturer-approved calibrations, and keep the service record for each unit.

Will the proposal apply to trucks already on the road?

Not as proposed. EPA would remove derates for newly manufactured engines and is only taking comment on whether in-use guidance should let makers update existing trucks. EPA has not issued that guidance, so current rules and manufacturer updates still govern trucks in service.

What happens to emissions warranty under the proposal?

EPA proposed keeping the MY2026 warranty periods for MY2027 and later engines instead of the longer 2023 periods. OOIDA urged EPA to keep 450,000-mile coverage. The proposal is not final, so confirm the warranty terms with the dealer in writing before ordering.

Where can I check the rule status?

Use EPA's proposed rule page for the amendments and nonconformance penalties and the Federal Register notice at 91 FR 43154, docket EPA-HQ-OAR-2026-0728. EPA last updated its page on August 31, 2026, so check both pages for any later final-rule notice before relying on this guide.

Wrap-up

The Bottom Line

DEF derate rules still apply to trucks on the road, and EPA's proposal to remove derates from new engines is not final as of November 2026. Current heavy-duty stages run from a 15 percent torque cut to 25 mph, and manufacturer updates delay them without repairing the fault. Fleets should log derates, control DEF supply and get calibration and warranty terms in writing.

Heavy Duty Journal will keep tracking the rule, and Michael Nielsen and the HDJ team publish emissions and compliance updates at heavydutyjournal.com. Michael Nielsen's coverage at heavydutyjournal.com ties each rule change to shop and fleet decisions. Check EPA's rule page before making a purchase or policy decision that depends on a final outcome.

Share This DEF Derate Guide

Know a fleet manager or technician dealing with DEF derates? Share this guide before the next derate hits a truck.

LinkedIn Facebook Twitter Reddit Threads Email Text

Leave a Comment

Your email address will not be published. Required fields are marked *